Panel Upgrades in Florida: When 100 Amps Isn’t Enough

A 100-amp panel was a perfectly reasonable heart for a Florida house in 1975 — a range, a water heater, window units, lights. The same house in 2026 is asked to run central air conditioning most of the year, a pool pump, a garage full of tools, and increasingly a Level 2 EV charger drawing as much as a small central AC system, all at once. That is how a panel that served three generations quietly becomes the bottleneck of the house. Here is how to tell when 100 amps is no longer enough, what the upgrade options look like, how the utility side works, and what Florida homeowners commonly pay.

Why 100 amps runs out faster in Florida

Electrical capacity is about coincident load — what runs at the same time. Florida stacks the deck: air conditioning runs eight to ten months a year rather than a few afternoons, pool pumps and heaters are everyday equipment rather than luxuries, and electric water heating is common. Layer on the loads of the last decade — EV charging, induction cooking, a mini-split in the garage or lanai — and the coincident load in an ordinary Florida home can crowd a 100-amp service in a way the original builder never imagined. The result shows up as nuisance breaker trips at first, and as a hard stop when you ask an electrician to add the next big circuit and the load calculation says no.

Signs your panel may need attention

  • Breakers that trip repeatedly, or a panel that is warm to the touch
  • A 60-amp or 100-amp service in a home now running central air, an EV charger, or a pool pump
  • No physical space left in the panel for new breakers, or tandem breakers already filling every slot
  • Panel brands that inspectors and insurers commonly flag, such as older Federal Pacific (Stab-Lok) or Zinsco equipment
  • Corrosion, rust, or double-tapped breakers found during a four-point inspection
  • An insurer asking for panel remediation before renewing a policy — common with older Florida homes
  • Plans on the horizon that add load: an EV, a pool, a home addition, or a standby generator and transfer switch, which land on the same service equipment

100A vs 150A vs 200A: how the sizes actually compare

The right size is settled by a load calculation — a licensed electrician tallies your square footage, fixed appliances, HVAC, and planned additions under the current National Electrical Code as adopted in Florida. As a general picture:

  • 100 amps remains workable for smaller homes with gas appliances or modest all-electric loads — but it leaves little headroom, and an EV charger plus central AC will usually consume whatever margin exists.
  • 150 amps is a middle step that suits many mid-size homes, though in practice the labor is similar to going larger, so it is chosen less often than the jump to 200.
  • 200 amps is the common target for Florida upgrades and the standard for new construction — comfortable headroom for central AC, electric water heating, a pool, and an EV charger, with slots to spare. When the service entrance is being rebuilt anyway, the incremental cost of 200 over 150 is usually modest, which is why most electricians steer the conversation there.

If the panel is failing but the load is genuinely small, a like-for-like replacement at the existing amperage is also a legitimate scope — the load calculation, not habit, should make the call.

Why a panel upgrade is not a DIY job in Florida

Replacing a panel means working at the service entrance of your home — the point where utility power arrives. It involves coordinating a disconnect with the utility, matching the panel and breakers to your service size, bonding and grounding correctly, and passing a county or municipal inspection. The Florida Building Code treats this as permitted electrical work: a permit is filed before the work starts and an inspector signs off after — our guide to Florida electrical permits explains how that process runs.

Under Chapter 489, Part II of the Florida Statutes, electrical contracting requires a state license issued through the Department of Business and Professional Regulation (DBPR). Hiring an unlicensed person for this kind of work is not a gray area: unlicensed electrical contracting is illegal in Florida, and homeowners who use unlicensed workers often discover the problem only when a sale, an insurance claim, or an inspection goes wrong.

Florida’s owner-builder exemption does allow a homeowner to pull their own permit and do or directly supervise the work on their own residence — with the home for their own occupancy, not for sale or lease, and with all the liability a contractor would otherwise carry. For something as consequential as a service panel, where an error can mean fire risk or a failed insurance inspection, most homeowners conclude the exemption is not worth it. If you would not feel comfortable explaining your grounding and bonding plan to an inspector, this is not the project to learn on.

The utility side: FPL, Duke, TECO, JEA and the disconnect

What surprises many homeowners is that a service upgrade is a three-party event: your contractor, the inspector, and your utility. Whether you are served by Florida Power & Light, Duke Energy Florida, Tampa Electric, JEA in the Jacksonville area, or a municipal utility, the sequence runs roughly the same way: the utility de-energizes the service, the contractor rebuilds the panel — and often the meter can and riser, which corrode fast in coastal Florida air — the inspector approves the work, and the utility reconnects. Expect the power to be off for a good part of the working day, and expect the reconnection to depend on the inspection clearing. A contractor who upgrades panels every week in your area knows the local utility’s process and builds it into the schedule; this coordination is one of the quiet things you are paying a professional for. Going from overhead to underground service, or moving the meter location, adds utility-side scope and cost of its own.

Aluminum-wiring-era homes: what a panel visit often uncovers

A large slice of Florida’s housing stock went up in the mid-1960s through the 1970s, when aluminum branch wiring was common. The panel is where that history surfaces: an electrician opening the enclosure sees the conductors, and aluminum branch circuits change the conversation. The panel replacement itself can proceed, but connections may need aluminum-rated treatment, and insurers frequently ask about remediation — commonly specialized connectors at devices and splices rather than a full rewire. If the wiring throughout the house is genuinely at the end of its life, the honest comparison is between remediation and a whole-home rewire, and a good contractor will price both paths rather than assume one.

What a panel upgrade typically costs in Florida

Costs vary with amperage, the condition of the service entrance, whether the meter can and riser also need replacement, and local permit fees. Florida homeowners commonly report totals in the range of roughly $1,500 to $4,000 or more for a like-for-like replacement or a 200-amp upgrade, with complex service changes — relocations, overhead-to-underground conversions, aluminum remediation added on — running higher. Permit fees commonly add $75–$300 depending on the jurisdiction. Treat any number, including these, as a starting point: get several written quotes that each spell out the permit, the equipment, and the inspection. Broader context on labor rates sits in our Florida electrician cost guide.

How to hire the right electrician for the job

Every contractor listed on this site is matched to a verifiable Florida DBPR electrical license, and the license number is shown on the listing so you can check it yourself — the license types are explained in our guide to verifying a Florida electrical license (EC vs ES vs ER). When you compare quotes for a panel upgrade:

  • Confirm the license is active and covers your area — a Certified (EC) license is valid statewide, while a Registered (ER) license is valid in its local jurisdiction
  • Ask who pulls the permit — the answer should always be the contractor, under their license
  • Ask for proof of liability insurance and workers’ compensation coverage
  • Get the scope in writing: panel make and model, amperage, grounding work, meter can and riser if included, permit and inspection included

Find a licensed electrician near you

You can browse state-licensed electrical contractors across Florida on this site — for example in Miami, Orlando, Tampa, and Cape Coral — or search the full directory by city. A panel upgrade is one of the highest-stakes electrical projects in a home; it deserves a licensed professional and a real permit. If your panel is showing the signs above, call the number shown at the top of this page to be connected with a licensed electrical contractor serving your part of Florida.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *